Serial Number DecalModel No. PFTL59011.0 Serial No. Write the serial number in the space above for reference.
107. Identify the Right Base Cover (91) and the Left Base Cover (88). Slide the Right Base Cover onto the Right Upright (85). Slide the Left Base Co
119. Set the console assembly face down on a soft surface to avoid scratching the console assem-bly. Remove and discard the two screws (B). Lift
1212. Set the console assembly on the Left Handrail (82) and the Right Handrail (83). Be careful not to pinch any wires. Insert the excess Upright W
1314. Make sure that all parts are properly tightened before you use the treadmill. If there are sheets of plas-tic on the treadmill decals, remove
14OPERATION AND ADJUSTMENTHOW TO CONNECT THE POWER CORDUse a Surge SuppressorYour treadmill, like other electronic equipment, can be damaged by sudden
15FEATURES OF THE CONSOLE The treadmill console offers a selection of features designed to make your workouts more effective and enjoyable. When you u
16HOW TO TURN ON THE POWERIMPORTANT: If the treadmill has been exposed to cold temperatures, allow it to warm to room tem-perature before turning on t
174. Change the incline of the treadmill as desired. To change the incline of the treadmill, press the Incline increase or decrease button or one
18HOW TO USE AN ONBOARD WORKOUT1. Insert the key into the console. See HOW TO TURN ON THE POWER on page 16. 2. Select an onboard workout. To
19THE INFORMATION MODEThe console features an information mode that keeps track of treadmill usage information. The information mode also allows you t
2TABLE OF CONTENTSWARNING DECAL PLACEMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
20 HOW TO FOLD THE TREADMILLTo avoid damaging the treadmill, adjust the incline to the lowest position before you fold the treadmill. Then, remove the
21Most treadmill problems can be solved by following the simple steps below. Find the symptom that applies, and follow the steps listed. If further as
22 Next, remove the three #8 x 3/4" Screws (1), and carefully pivot the Motor Hood (62) off. Locate the Reed Switch (73) and the Magnet (47)
23SYMPTOM: The walking belt is off-center or slips when walked ona. If the walking belt is off-center, rst remove the key and UNPLUG THE POWER CORD
24EXERCISE GUIDELINESThese guidelines will help you to plan your exercise program. For detailed exercise information, obtain a reputable book or consu
25SUGGESTED STRETCHESThe correct form for several basic stretches is shown at the right. Move slowly as you stretch —never bounce.1. Toe Touch Stretch
26PART LIST Key No. Qty. Description Key No. Qty. Description 1 23 #8 x 3/4" Screw 2 4 #10 x 3/4" Screw 3 2 Console Clamp 4 6
27 Key No. Qty. Description Key No. Qty. Description 101 1 Console 102 1 Console Frame 103 1 Left Tray 104 1 5/32" Hex Key * – Us
28EXPLODED DRAWING AModel No. PFTL59011.0 R0512A865120212134332832324343304530303039403636364745463644414948543960555656465859615718102423181919202430
29EXPLODED DRAWING BModel No. PFTL59011.0 R0512A15151515741873373737111172222282869707168626476757265162828316766777978161663
3IMPORTANT PRECAUTIONS1. Before beginning any exercise program, con-sult your physician. This is especially impor-tant for persons over age 35 or pe
30EXPLODED DRAWING CModel No. PFTL59011.0 R0512A858382383844138447111411888190590590596968273589899592929490594252635359798871010893273591711111441387
31EXPLODED DRAWING DModel No. PFTL59011.0 R0512A1031018011110019953533310252291134111111
Part No. 317367 R0512A Printed in USA © 2012 ICON IP, Inc.ORDERING REPLACEMENT PARTSTo order replacement parts, please see the front cover of this ma
420. Never leave the treadmill unattended while it is running. Always remove the key, unplug the power cord, and press the power switch into the off
5Thank you for selecting the revolutionary PROFORM® 515 TX treadmill. The 515 TX treadmill offers an im-pressive selection of features designed to mak
6ASSEMBLYTo hire an authorized service technician to assemble the treadmill, call 1-800-445-2480.Assembly requires two persons. Set the treadmill in a
72. See the inset drawing. Cut the plastic tie near the Upright Wire (87). Attach a Wheel (96) to the Base (95) with a 3/8" x 2" Bolt (8
83. Identify the Right Upright (85), which is marked with a “Right” sticker. Hold the Right Upright near the Base (95) as shown. See the inset dra
96. Hold the Left Upright (84) against the Base (95). Insert two 3/8" x 4" Screws (7) with two 3/8" Star Washers (11) and a 3/8"
Comments to this Manuals