USER'S MANUALQUESTIONS?As a manufacturer, we are committed to providing completecustomer satisfaction. If youhave questions, or if there aremissi
101448481084101101014848535314. Insert a 2” Round Inner Cap (101) into the end of aButterfly Arm (10).Attach a Butterfly Handle (53) to the Butterfly
20.Locate and open the parts bags labeled “CABLEASSEMBLY” and “PULLEYS.”Locate the Butterfly Cable (73), which is theshorter cable of the two that hav
1222. Remove the preassembled 3/8” x 2” Bolts (54) fromone set of Adjustable Pulley Plates (23).Wrap the Butterfly Cable (73) around a 3 1/2”Pulley (2
1326. Wrap the Ab Cable (47) around a 3 1/2” Pulley (24).Insert the Ab Cable down through the Press TopFrame (9). Slide a 3/8” Washer (48) and a 5/8”
1430. Locate the Weight Cable (72). Note that one endof the Weight Cable has a bolt on it, and theother end has a ball on it. Lay the Weight Cable (72
1535363734. Wrap the Weight Cable (72) around a 3 1/2” Pulley(24). Attach the Pulley and a Cable Trap (25) to theButterfly Upright (1) with a 3/8” x 4
1638. Wrap the Weight Cable (72) around a 3 1/2” Pulley(24). Attach the Pulley and a Cable Trap (25)between the lowest holes in the Adjustable PulleyP
1742. Locate the Leg Press Cable (75). Attach the LegPress Cable to the indicated side of the PressUpright (2) with a 3/8” x 3 3/4” Bolt (102) and a 3
1846. Remove the 3/8” Nylon Locknut (50) from the indi-cated 3/8” x 5 1/2” Bolt (55). Wrap the Leg Press Cable (75) around a 3 1/2”Pulley (24). Secure
1950. Locate and open the parts bag labeled “SEATASSEMBLY.”Attach a Seat (13) to the brackets on the ButterflySeat Frame (14) using four 1/4” x 3/4” B
2TABLE OF CONTENTSIMPORTANT PRECAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
20545556914633954. Lubricate a 1/2” x 4” Bolt (68). Attach the FootPress Plate (29) to the Press Leg Lever (90) withthe Bolt and a 1/2” Nylon Jamnut (
21ADJUSTMENTSThe instructions below describe how each part of the weight system can be adjusted. Refer to the exerciseguide accompanying this manual t
22ATTACHING THE AB STRAP TO THE AB PULLEYSTATIONAttach the Ab Strap (81) to the Ab Cable (47) at the abpulley station with a Cable Clip (69). ADJUSTIN
23WEIGHT RESISTANCE CHARTThis chart shows the approximate weight resistance at each weight station. “Top” refers to the 10 lb. top weight.The other nu
TROUBLE-SHOOTING AND MAINTENANCE Inspect and tighten all parts each time you use the weight system. Replace any worn parts immediately. Theweight syst
25CABLE DIAGRAMSThe cable diagrams on this page and the next page show the proper routing of the Leg Press Cable (75), the AbCable (47), the Butterfly
26Weight Cable (72)231—Low Pulley481112—WeightStack765Cable ID72 47 75 73910
5/16" Nylon Jamnut (105)Cable Clip (69)"V" Pulley (27)(Not shown to scale)3 1/2" Pulley (24)(Not shown to scale)Retainer Ring (31)
5/16" x 2 1/4" Shoulder Bolt (79)3/8" x 1" Bolt (84)3/8" x 1 3/4" Bolt (57)3/8" x 6" Bolt (59)1/2" x 4&qu
2" Square Inner Cap (28)1 1/2" Square Inner Cap (35)1 1/2" x 2 1/2” Inner Cap (83)2 1/2" Square Inner Cap (76)3” Round Inner Cap (
IMPORTANT PRECAUTIONS31. Read all instructions in this manual and inthe accompanying literature before using theweight system.2. It is the responsibil
PART LIST—Model No. PFSY59001 R0402ANote: “#” indicates a non-illustrated part. Specifications are subject to change without notice. Key No. Qty. Desc
92924939492325242524235054232524252423504435498665771016586776425246096683625245086829366836502524252459907810248508040205083 660242550504950242550750
ORDERING REPLACEMENT PARTSTo order replacement parts, simply call our Customer Service Department toll-free at 1-800-999-3756, Mondaythrough Friday,
4BEFORE YOU BEGINASSEMBLED DIMENSIONS: Height: 76.0 in.Width: 86.5 in. Length: 91.5 in. Foot PlateLow PulleyStationHigh Pulley StationLat BarLeg Lever
5ASSEMBLYMake sure you have the following tools:• Two (2) adjustable wrenches• One (1) standard screwdriver• One (1) phillips screwdriver• One (1)
1.Locate and open the parts bags labeled “FRAMEASSEMBLY.”See the inset drawing. Insert two 1 1/2” x 2 1/2”Inner Caps (83) and two 3/8” x 2” Carriage B
4. Attach the Butterfly Seat Frame (14) to the ButterflyUpright (1) with two 3/8” x 3 3/4” Bolts (102), two3/8” Washers (48), and two 3/8” Nylon Lockn
88948484889516504821Slot158. See the inset drawing. Insert two Weight Inserts(56) into each Weight (21).Set the two Weight Bumpers (51) over the holes
94862504833911. Secure the Press Top Frame (9) to the Butterfly TopFrame (33) with two 3/8” x 3 1/4” Bolts (62), two3/8” Washers (48), and two 3/8” Ny
Comments to this Manuals